NUMBER PRESS WILL NOT SAVE ON WINDOS 10 INSTALL
NUMBER PRESS WILL NOT SAVE ON WINDOS 10 DRIVER
NUMBER PRESS WILL NOT SAVE ON WINDOS 10 PC
NUMBER PRESS WILL NOT SAVE ON WINDOS 10 LICENSE

NUMBER PRESS WILL NOT SAVE ON WINDOS 10 PC

NOTE: If you have added the PC ServeRAID II adapter into the server, see Appendix A for hard disk configuration and operating system installation instructions.Ĭonfiguring Hard Drives with the Integrated SCSI:ġ. If you have installed any additional supported ISA or EISA adapters you wish to configure into the system's hardware, see Appendix D for further instructions on using the 'IBM Netfinity 7000 System CD-ROM' to configure those devices. From the Advanced screen, press the right arrow button twice, then highlight ' Exit Saving Changes' and press Enter twice to exit setup.ħ. To change the setting on either option, highlight it, then press Enter, highlight your new choice, then press Enter again.Ħ. Verify that MP Version is set to '1.4,' then press Esc. Highlight 'Advanced Chipset Configuration' and press Enter.ĥ.

Press the right arrow key to bring up the Advanced screen.

Next press Esc to return to the previous screen.Ĥ. 'Fourth Boot Device' is 'Disabled,' or one of the other available settings if you desire a fourth boot option. Highlight Boot Options and verify that 'First Boot Device' is 'CD-ROM,' 'Second Boot Device' is 'Floppy,' 'Third Boot Device' is 'Hard Disk,' and Under the Main heading, verify the time and date settings.ģ. Power on the system and press to enter SETUP.Ģ.

NUMBER PRESS WILL NOT SAVE ON WINDOS 10 INSTALL

Next, install Windows NT Server 4.0 Service Pack 3 according to the instructions that follow, then add the additional RAM to the server.ġ. IMPORTANT NOTE: If you intend to operate this server with more than 2 GB of RAM, be sure to install Windows NT Server 4.0 with 2 GB of RAM or less installed in the server. Install the desired number of hot-swap hard drives into the hot-swap bays beginning at the top of a backplane and proceeding downward. Install a supported network adapter into one of the available ISA, EISA or, PCI expansion slots and properly connect its external port to a network cable.Ħ. Return the shuttle to its original position and tighten the four thumb screws.ĥ. Unhook the two SCSI cables (part number 01K6525) from the onboard Adaptec controllers and reattach them to the first two connectors on the PC ServeRAID II adapter.Ĥ. Looking at the rear of the system, loosen the four thumb screws at the four corners of the shuttle and pull the shuttle out, exposing the back of the hot-swap backplanes. Verify that the PC ServeRAID II Adapter is firmly in one of the system's primary PCI expansion slots (P1 - P4). If you have installed a PC ServeRAID II Adapter: Looking at the rear of the system, verify that the SCSI cables (part number 01K6525) run from the on-board Adaptec controllers, located near the top right corner of the system board, to the top of the hot-swap backplanes. This procedure streamlines the install process. After the operating system is booting without errors, add these devices one at a time. If a tape drive or external SCSI devices will be used, just disconnect them temporarily. (For example, if installing multiple network adapters, only install one at this time. For the initial install, it is recommended that you remove all adapters and devices that are not required to get the base operating system installed. Looking at the rear of the system, loosen the two thumb screws at the top of the system and remove the top access panel.Ģ. (For users who are very familiar with SCSI, hardware, and install process, jump to Appendix B )ġ. (For IBM PC sites in other countries, begin at: This is available from Microsoft's web site or FTP site (see next section for more information).

Microsoft NT Server 4.0 Service Pack 3 (filename NT4SP3_I.EXE). PC ServeRAID Configuration Diskette (see next section for more information).

NUMBER PRESS WILL NOT SAVE ON WINDOS 10 DRIVER

PC ServeRAID Device Driver and Utilities Diskette Netfinity 7000 System Configuration Diskette 'Netfinity 7000 System CD-ROM.' If this CD is damaged or missing, the equivalent files can be obtained by downloading the following diskettes: Copies are not bootable).įour blank diskettes, label one 'NT 4.0 AIC-78XX Driver,' labeled one 'NT 4.0 PC ServeRAID II Driver,' label one 'Emergency Repair Diskette,' label the last 'Netfinity 7000 SCU Configuration Save Diskette.'

NUMBER PRESS WILL NOT SAVE ON WINDOS 10 LICENSE

License copy of Microsoft NT Server 4.0 (note: if you plan to install using a copy of the CD instead of an original, you will have to install using diskettes. Supported network card (refer to for a list of supported options and part numbers for your IBM Server). Supported hard drive (refer to for a list of supported options and part numbers for your IBM Server).

Number press will not save on windos 10